Honda Accord

1998-1999 of release

Repair and car operation

Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
- Brake system
   System of anti-blocking of brakes (ABS) - the general information and codes of malfunctions
   Replacement of brake shoes of disk brake mechanisms
   Removal and installation of supports of disk brake mechanisms
   Condition check, removal and installation of a brake disk
   Replacement of boots of drum-type brake mechanisms of back wheels
   Removal and installation of wheel cylinders
   Removal and installation of the main brake cylinder
   Check of a condition and replacement of brake lines and hoses
   Pumping of brake system
   Check of serviceability of functioning/tightness, removal and installation of assembly of the vacuum amplifier of brakes
   Adjustment of the parking brake
   Cable replacement (ов) drive of the parking brake
   Check of serviceability of functioning, replacement and adjustment of the sensor switch of stoplights
   Check of serviceability of functioning and replacement of the sensor switch of level of brake liquid
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes

d42fda4b d42fda4b

Condition check, removal and installation of a brake disk

Procedure is equally applicable to disk brake mechanisms both forward, and back wheels.

Condition check


1. Weaken fastening nuts to Coca, поддомкратьте the car and establish it on props. Remove the corresponding wheel, then screw pair of wheel nuts back on fixing hairpins, having enclosed under them washers in thickness of 3 mm for the purpose of fixing of a brake disk (if two screws of fastening of a disk are not turned out yet, need for a navorachivaniye of nuts disappears). At check of a disk of the back brake mechanism do not forget to release the parking brake.
2. Remove a brake support (see. The section Removal and installation of supports of disk brake mechanisms) also tie up it aside a wire to a suspension bracket element, without disconnecting a brake hose.

3. Make visual check of a condition of a working surface of a disk. Easy defects can be eliminated by means of a fine-grained emery paper. For removal of furrows by depth a disk it is necessary to subject more than 0.38 mm to a pro-point. Remember that survey of a disk should be made from its both parties.

4. If during braking pedal pulsations were noticed, it is necessary to estimate size of lateral palpation of a brake disk. Fix a tsiferblatny measuring instrument of plunzherny type (DTI) at distance about 12.7 mm from external edge of a disk.

5. Null the device and start to rotate a disk. The result of measurement should not fall outside the limits the admissible range stipulated in Specifications, otherwise it is necessary to give a disk to a pro-point.

Originators of the real Management recommend to make a pro-point of disks regardless of their condition for the purpose of removal from working any surfaces of defects. As a last resort it is possible to be limited to disk processing by a fine-grained emery paper.

6. At a pro-point of a disk it is necessary to give particular attention to observance of requirements of Specifications to its minimum admissible thickness. On a face surface of a disk the corresponding marking is provided.

7. Measurement of thickness of a disk is made by means of a micrometer.



1. Turn out two bolts of fastening of an anchor bracket of a support to a rotary fist,

2. or (on the brake mechanism of a back wheel) bolts of fastening of a bracket to stupichny assembly. Remove a bracket.

3. Remove two wheel nuts used for fixing of a disk on a nave / turn out two fixing screws. Remove a disk from a wheel nave.

4. If the disk "became attached" to a nave, it can be squeezed out by a vvorachivaniye in fixing openings of pair of bolts of the suitable size. Tighten bolts evenly and gradually until the disk completely will not be released. At removal of a disk try not to damage a carving of hairpins of fastening of a wheel.



1. Accurately put on a disk a nave (again try not to damage wheel hairpins). Screw and strongly tighten fixing screws.
2. Establish on a disk an anchor bracket of a support. Tighten bolts of fastening of a bracket and a support with demanded effort.
3. Establish into place a wheel, lower the car on the earth and tighten wheel nuts with demanded effort (see. Specifications to Head of Control and routine maintenance). Several times squeeze out a brake pedal / cock the lever of the parking brake for the purpose of a usadka of blocks on a disk. If brake hoses were not disconnected, need for a prokachivaniye of hydraulic system is absent. Before starting car operation, make sure of serviceability of functioning of brakes.