Honda Accord

1998-1999 of release

Repair and car operation

Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
+ Systems of cooling, heating
- Power supply system and release
   Sbrasyvaniye of pressure in a power supply system
   Check of serviceability of functioning of the fuel pump, measurement of pressure of fuel
   Check of a condition and replacement of fuel lines
   Removal and installation of the fuel pump
   Check of a condition and sensor replacement
   Removal and installation of a fuel tank
   Cleaning and repair of a fuel tank - general information
   Removal and installation of assembly of an air purifier
   Removal, installation and adjustment of a cable of an accelerator
   System of electronic injection of fuel (EFI) - the general information
   Check of serviceability of functioning of system of injection
   Removal and installation of the case of a throttle
   Removal and installation of a regulator of pressure of fuel
   Removal and installation of the fuel highway and fuel injectors
   Release system - the general information
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes

d42fda4b d42fda4b

Check of a condition and replacement of fuel lines

See preventions at the beginning of pressure Sbrasyvaniye's Section in a power supply system.


1. Before starting service of fuel lines or their shtutserny connections it is necessary to dump pressure in a power supply system (see. Undressed Sbrasyvaniye pressure in a power supply system).
2. Lines of a fuel path of a power supply system are laid between a fuel tank and an impellent compartment. Steel tubes and flexible fuel hoses fasten to the car bottom by means of clips and screw fixture. Each time when the car rises over the earth with any purpose (for example, for survey or replacement of components of system of production of the fulfilled gases), try to use a case and to check a condition of fuel lines and their shtutserny connections. Attentively examine all hoses and tubes of a fuel path on existence of cracks, twisting, deformations and other damages.
3. At identification of signs of internal pollution or passableness violation the corresponding section of a fuel path is necessary for removing and blowing the compressed air. Without fail check also a condition of the mesh filter of a toplivozabornik of the pump (see. Section Removal and installation of the fuel pump).

Steel tubes


1. Use as replaceable sections only high-strength steel tubes of the proved producers.
2. Remember that copper and aluminum tubes are not capable to sustain vibrating loadings arising in use the car.
3. Do not forget that fuel lines on the models equipped with system of injection, should maintain high internal pressure.
4. Often in firm shops of automobile accessories it is possible to get the sections of metal tubes equipped with carving shtutserny nozzles. During the easing and a tightening of shtutserny connections use two wrenches to avoid a provorachivaniye of a reciprocal part of the socket. Without fail check a condition of shtutserny connections of sealing rings used for sealing. The worn-out or mechanically damaged rings at once replace. Try to use as replaceable components only firm details.

Flexible hoses

At replacement of fuel hoses use only firm components calculated on high internal pressure.

Flexible fuel hoses should be laid not closer than in 10 cm from components of system of production of the fulfilled gases and is not closer than in 25 cm from the catalytic converter. Watch, that fuel lines did not adjoin to body elements and suspension bracket components. The minimum admissible size of a gap makes 6.3 mm.

Removal and installation


1. Dump pressure in a power supply system (see. Undressed Sbrasyvaniye pressure in a power supply system).

2. Liberate section of a fuel path subject to dismantle from intermediate clamps of fastening it to the car bottom. Remark: To Shtutsernye sockets of fast joining are not subject to regenerative repair and in case of their exit out of operation the corresponding section of the line should be replaced assembled.

3. Installation is made upside-down. Do not forget to replace sealing rings of carving shtutserny connections. Before a zashchelkivaniye of sockets of fast joining track correctness of combination of doggies of lock uvulas with reciprocal grooves.


The damaged sections of fuel lines (tubes or hoses) should be removed and replaced new, firm production.