Honda Accord

1998-1999 of release

Repair and car operation

Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
- Systems of cooling, heating
   Antifreeze - general information
   Check of serviceability of functioning and thermostat replacement
   Check of a condition of fans of system of cooling and chains of their inclusion, replacement of fans
   Removal and installation of a radiator and broad tank of system of cooling
   Check of a condition of the water pump
   Replacement of the water pump
   Check of serviceability of functioning and replacement of the block of the sensor of a measuring instrument of temperature of cooling liquid
   Check of serviceability of functioning of the driving electromotor of the fan of a heater and condition of components of its electric chain, replacement of components
   Removal and installation of the electromotor of a drive of the fan of a heater
   Removal and installation of assembly of the control panel by functioning of a heater and air conditioner, adjustment of a driving cable
   Removal and installation of the heat exchanger of a heater
   Check of serviceability of functioning and service of systems of heating and air conditioning
   Check of an electric chain of the coupling of coupling of the To/in compressor
   Removal and receiver dehumidifier installation To/in
   Removal and To/in compressor installation
   Removal and To/in condenser installation
   Removal and To/in evaporator installation with the broad valve
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes

d42fda4b d42fda4b

Removal and installation of a radiator and broad tank of system of cooling

Do not start performance of procedures before complete cooling of the engine. See also prevention at the beginning of the Section Antifreeze - general information.

Broad tank


1. The broad tank of system of cooling is located near a radiator in right forward (4-cylinder models) or right forward (V6 models) to a corner of an impellent compartment (near the storage battery).

2. Walk on a perelivny hose from a radiator mouth to the top part of a broad tank. Uncover together with the hose connected to it. Remove a tank, having pulled it vertically up and having liberated from a basic arm.

3. Merge cooling liquid from a broad tank in the prepared capacity.
4. Wash out a tank, wipe it outside and check on existence of cracks and other damages. In case of need make replacement. Level of the liquid which was in a tank should be read easily through translucent walls.
5. Installation is made upside-down.




1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Cock the parking brake and prop up back wheels protivootkatny boots. To Poddomkratta a car front also establish it on props. At the corresponding complete set remove the antispray screen of a radiator.

3. Empty cooling system (see. Head of Control and routine maintenance). If replacement of cooling liquid was made recently, keep for further use (see the prevention in the Section Antifreeze - general information).

4. On models from AT disconnect from a radiator of the line of a path of cooling of ATF (see an accompanying illustration). Prepare for collecting spilled liquid, at once закупорьте the open ends of tubes and unions.

5. Disunite the socket of electroconducting of the fan of system of cooling (see. Section Check of a condition of fans of system of cooling and chains of their inclusion; replacement of fans).

6. Release collars and disconnect from a radiator both (top and bottom) hoses. If hoses "became attached" to connecting branch pipes, use nippers, or a knife (with the subsequent replacement of hoses). Disconnect also a hose going to a broad tank.

7. Remove fans (see. Section Check of a condition of fans of system of cooling and chains of their inclusion; replacement of fans).

8. To Otboltita also remove small arms of fastening of the upper edge of a radiator to a bearing beam.

9. Carefully take a radiator from an impellent compartment. Try not to spill cooling liquid on the painted body panels and do not cut fingers about sharp plates of the heat exchanger.
10. After removal from the car the radiator can be checked on existence of signs of leaks, damages and violations of internal passableness of the heat exchanger. Any repair should be made only in the conditions of a specialized workshop with use of the necessary equipment.
11. Remains of insects and vegetation can be removed from space between heat exchanger plates a way of blowing by the compressed air (do not forget to put on goggles!), or vychishcheniye soft brush. Try not to bend thin plates of the heat exchanger and not to cut about them fingers.
12. Check a condition of rubber support of a radiator, in case of need make replacement of the failed components.



1. Installation is made upside-down. Track correctness of placement of a radiator on the support.
2. On completion of installation fill in in system cooling liquid of demanded structure (see. Head of Control and routine maintenance), in case of need let out from a path air jams via the special final gate.
3. Start the engine and check it on existence of signs of leaks. Warm up the engine to normal working temperature (both hoses of a radiator should become hot to the touch). Check level of cooling liquid, in case of need add the corresponding quantity of a mix.
4. On models from AT check ATF level, in case of need add.