Honda Accord

1998-1999 of release

Repair and car operation

Honda Chord
+ Honda Accord brand Cars
+ Settings and routine maintenance
+ Engine
- Systems of cooling, heating
   Antifreeze - general information
   Check of serviceability of functioning and thermostat replacement
   Check of a condition of fans of system of cooling and chains of their inclusion, replacement of fans
   Removal and installation of a radiator and broad tank of system of cooling
   Check of a condition of the water pump
   Replacement of the water pump
   Check of serviceability of functioning and replacement of the block of the sensor of a measuring instrument of temperature of cooling liquid
   Check of serviceability of functioning of the driving electromotor of the fan of a heater and condition of components of its electric chain, replacement of components
   Removal and installation of the electromotor of a drive of the fan of a heater
   Removal and installation of assembly of the control panel by functioning of a heater and air conditioner, adjustment of a driving cable
   Removal and installation of the heat exchanger of a heater
   Check of serviceability of functioning and service of systems of heating and air conditioning
   Check of an electric chain of the coupling of coupling of the To/in compressor
   Removal and receiver dehumidifier installation To/in
   Removal and To/in compressor installation
   Removal and To/in condenser installation
   Removal and To/in evaporator installation with the broad valve
+ Power supply system and release
+ engine Electric equipment
+ Engine management
+ gear shifting Box
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ electric equipment Schemes

d42fda4b d42fda4b

Check of serviceability of functioning and thermostat replacement

Do not open a cover of a radiator and do not remove the thermostat before complete cooling of the engine! See also prevention at the beginning of the Section Antifreeze - general information.



1. Before finally affirming as opinion on a thermostat exit out of operation, check level of cooling liquid in system, a condition and effort of a tension of a driving belt (see. Head of Control and routine maintenance), and also serviceability of functioning of a measuring instrument of temperature.
2. One of possible the reason of too slow warming up of the engine (according to measuring instrument indications) is thermostat jamming in open situation. Replace the thermostat new.
3. In case of an overheat of the engine touch a hand the top hose of a radiator. If the hose is not heated up, possibly, the thermostat is jammed in a closed position, blocking circulation of cooling liquid through a radiator. Replace the thermostat.

At all do not maintain the car with the removed thermostat! Feedback of the onboard processor that will lead to increase of toxicity of the fulfilled gases and excessive increase in fuel consumption thus can become torn.

4. If the top hose is heated up, it means that cooling liquid regularly circulates through a radiator, i.e. the thermostat is open. Address to materials of the Section devoted to diagnostics of malfunctions of system of cooling.



1. Disconnect a negative wire from the battery.

If the stereosystem established on the car is equipped with a security code before disconnecting the battery make sure that have the correct combination for audiosystem input in action!

2. Merge cooling liquid from a radiator (see. Head of Control and routine maintenance). If replacement of a mix was made recently, keep it for further use.
3. Walk on the top radiatorny hose to the engine and find a cover of a casing of the thermostat.
4. Weaken a collar and remove a hose from the connecting branch pipe. If the hose "became attached", grasp it nippers (as it is possible closer to a cut) and try повращать on a branch pipe for the purpose of destruction of a holding layer of deposits. The old hose subject to replacement can be cut simply (try not to scratch a branch pipe).
5. If the surface of a branch pipe contacting to a hose is struck with corrosion, or mechanically damaged, it is meaningful to replace a cover of a casing of the thermostat.

6. Turn out fixing bolts and uncover a thermostat casing.

If the cover "became attached", обстучите its hammer with soft the brisk. Prepare for collecting spilled liquid.

7. Try to remember adjusting position of the thermostat (a klapanny finger up), then take it from a casing.
8. Remove from casing and cover surfaces all traces of hermetic and a material of old laying.

9. Replace rubber sealing laying of the thermostat.

10. Establish the thermostat in a casing (do not apply any hermetic). Track, that it appeared is developed by a pumping finger up, and the equipped spring the party to the engine.

11. Establish into place a cover and fix it bolts, having tightened the last with demanded effort.
12. Connect to a cover branch pipe a hose and strongly fix it a collar. Return into place all components acting in film for the purpose of ensuring access.
13. Fill in in system necessary amount of cooling liquid (see. Head of Control and routine maintenance).
14. Start the engine and check it on existence of leaks and serviceability of functioning of the thermostat (see paragraphs with 2 on 4).